STM32F103ZET_JDASMBIC/Src/main.c

/* USER CODE BEGIN Header */
/**
  ******************************************************************************
  * @file           : main.c
  * @brief          : Main program body
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */
/* USER CODE END Header */

/* Includes ------------------------------------------------------------------*/
#include "main.h"

/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */

/* USER CODE END Includes */

/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */

/* USER CODE END PTD */

/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */

/* USER CODE END PD */

/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */

/* USER CODE END PM */

/* Private variables ---------------------------------------------------------*/
ADC_HandleTypeDef hadc1;
DMA_HandleTypeDef hdma_adc1;

UART_HandleTypeDef huart1;

/* USER CODE BEGIN PV */

/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_DMA_Init(void);
static void MX_ADC1_Init(void);
static void MX_USART1_UART_Init(void);
static void MX_NVIC_Init(void);
/* USER CODE BEGIN PFP */

/* USER CODE END PFP */

/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

/**
  * @brief  The application entry point.
  * @retval int
  */
int main(void)
{
  /* USER CODE BEGIN 1 */

  /* USER CODE END 1 */
  

  /* MCU Configuration--------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* USER CODE BEGIN Init */

  /* USER CODE END Init */

  /* Configure the system clock */
  SystemClock_Config();

  /* USER CODE BEGIN SysInit */

  /* USER CODE END SysInit */

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_DMA_Init();
  MX_ADC1_Init();
  MX_USART1_UART_Init();

  /* Initialize interrupts */
  MX_NVIC_Init();
  /* USER CODE BEGIN 2 */

  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
    /* USER CODE END WHILE */

    /* USER CODE BEGIN 3 */
  }
  /* USER CODE END 3 */
}

/**
  * @brief System Clock Configuration
  * @retval None
  */
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
  RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};

  /** Initializes the CPU, AHB and APB busses clocks 
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI_DIV2;
  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL15;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }
  /** Initializes the CPU, AHB and APB busses clocks 
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
  {
    Error_Handler();
  }
  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC;
  PeriphClkInit.AdcClockSelection = RCC_ADCPCLK2_DIV6;
  if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
  {
    Error_Handler();
  }
}

/**
  * @brief NVIC Configuration.
  * @retval None
  */
static void MX_NVIC_Init(void)
{
  /* USART1_IRQn interrupt configuration */
  HAL_NVIC_SetPriority(USART1_IRQn, 0, 0);
  HAL_NVIC_EnableIRQ(USART1_IRQn);
}

/**
  * @brief ADC1 Initialization Function
  * @param None
  * @retval None
  */
static void MX_ADC1_Init(void)
{

  /* USER CODE BEGIN ADC1_Init 0 */

  /* USER CODE END ADC1_Init 0 */

  ADC_ChannelConfTypeDef sConfig = {0};

  /* USER CODE BEGIN ADC1_Init 1 */

  /* USER CODE END ADC1_Init 1 */
  /** Common config 
  */
  hadc1.Instance = ADC1;
  hadc1.Init.ScanConvMode = ADC_SCAN_ENABLE;
  hadc1.Init.ContinuousConvMode = DISABLE;
  hadc1.Init.DiscontinuousConvMode = DISABLE;
  hadc1.Init.ExternalTrigConv = ADC_SOFTWARE_START;
  hadc1.Init.DataAlign = ADC_DATAALIGN_RIGHT;
  hadc1.Init.NbrOfConversion = 2;
  if (HAL_ADC_Init(&hadc1) != HAL_OK)
  {
    Error_Handler();
  }
  /** Configure Regular Channel 
  */
  sConfig.Channel = ADC_CHANNEL_0;
  sConfig.Rank = ADC_REGULAR_RANK_1;
  sConfig.SamplingTime = ADC_SAMPLETIME_1CYCLE_5;
  if (HAL_ADC_ConfigChannel(&hadc1, &sConfig) != HAL_OK)
  {
    Error_Handler();
  }
  /** Configure Regular Channel 
  */
  sConfig.Rank = ADC_REGULAR_RANK_2;
  if (HAL_ADC_ConfigChannel(&hadc1, &sConfig) != HAL_OK)
  {
    Error_Handler();
  }
  /* USER CODE BEGIN ADC1_Init 2 */

  /* USER CODE END ADC1_Init 2 */

}

/**
  * @brief USART1 Initialization Function
  * @param None
  * @retval None
  */
static void MX_USART1_UART_Init(void)
{

  /* USER CODE BEGIN USART1_Init 0 */

  /* USER CODE END USART1_Init 0 */

  /* USER CODE BEGIN USART1_Init 1 */

  /* USER CODE END USART1_Init 1 */
  huart1.Instance = USART1;
  huart1.Init.BaudRate = 115200;
  huart1.Init.WordLength = UART_WORDLENGTH_8B;
  huart1.Init.StopBits = UART_STOPBITS_1;
  huart1.Init.Parity = UART_PARITY_NONE;
  huart1.Init.Mode = UART_MODE_TX_RX;
  huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;
  huart1.Init.OverSampling = UART_OVERSAMPLING_16;
  if (HAL_UART_Init(&huart1) != HAL_OK)
  {
    Error_Handler();
  }
  /* USER CODE BEGIN USART1_Init 2 */

  /* USER CODE END USART1_Init 2 */

}

/** 
  * Enable DMA controller clock
  */
static void MX_DMA_Init(void) 
{
  /* DMA controller clock enable */
  __HAL_RCC_DMA1_CLK_ENABLE();

  /* DMA interrupt init */
  /* DMA1_Channel1_IRQn interrupt configuration */
  HAL_NVIC_SetPriority(DMA1_Channel1_IRQn, 0, 0);
  HAL_NVIC_EnableIRQ(DMA1_Channel1_IRQn);

}

/**
  * @brief GPIO Initialization Function
  * @param None
  * @retval None
  */
static void MX_GPIO_Init(void)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};

  /* GPIO Ports Clock Enable */
  __HAL_RCC_GPIOE_CLK_ENABLE();
  __HAL_RCC_GPIOC_CLK_ENABLE();
  __HAL_RCC_GPIOF_CLK_ENABLE();
  __HAL_RCC_GPIOA_CLK_ENABLE();
  __HAL_RCC_GPIOB_CLK_ENABLE();
  __HAL_RCC_GPIOD_CLK_ENABLE();
  __HAL_RCC_GPIOG_CLK_ENABLE();

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOE, ATT_EN_1_8G_DL1_Pin|ATT_EN_1_8G_DL2_Pin|ATT_EN_1_8G_UL1_Pin|ATT_EN_1_8G_UL2_Pin 
                          |ATT_EN_1_8G_UL3_Pin|PATH_EN_2_1G_DL_Pin|PATH_EN_2_1G_UL_Pin, GPIO_PIN_RESET);

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOC, ATT_EN_1_8G_UL4_Pin|PATH_EN_1_8G_DL_Pin|PATH_EN_1_8G_UL_Pin|PLL_EN_3_5G_L_Pin 
                          |PLL_EN_3_5G_H_Pin, GPIO_PIN_RESET);

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOF, PLL_EN_1_8G_DL_Pin|PLL_EN_1_8G_UL_Pin|ATT_EN_2_1G_DL1_Pin|ATT_EN_2_1G_DL2_Pin 
                          |ATT_EN_2_1G_UL1_Pin|ATT_EN_2_1G_UL2_Pin|ATT_EN_2_1G_UL3_Pin|ATT_EN_2_1G_UL4_Pin, GPIO_PIN_RESET);

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOD, PLL_DATA_Pin|PLL_CLK_Pin|ATT_DATA_Pin|ATT_CLK_Pin 
                          |DA_LDAC_Pin|ATT_CLK_3_5G_Pin|ATT_EN_3_5G_Pin|ATT_DATA_3_5G_DL_Pin 
                          |ATT_DATA_3_5G_UL_Pin|ATT_DATA_3_5G_COM1_Pin|ATT_DATA_3_5G_COM2_Pin|ATT_DATA_3_5G_COM3_Pin 
                          |PATH_EN_3_5G_L_Pin, GPIO_PIN_RESET);

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOG, DA_SYNC_Pin|DA_SCLK_Pin|DA_DIN_Pin|_T_SYNC_UL_Pin 
                          |T_SYNC_UL_Pin|_T_SYNC_DL_Pin|T_SYNC_DL_Pin|PATH_EN_3_5G_DL_Pin 
                          |PATH_EN_3_5G_UL_Pin|PLL_ON_OFF_3_5G_L_Pin|PLL_ON_OFF_3_5G_H_Pin, GPIO_PIN_RESET);

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOB, PLL_EN_2_1G_DL_Pin|PLL_EN_2_1G_UL_Pin, GPIO_PIN_RESET);

  /*Configure GPIO pins : ATT_EN_1_8G_DL1_Pin ATT_EN_1_8G_DL2_Pin ATT_EN_1_8G_UL1_Pin ATT_EN_1_8G_UL2_Pin 
                           ATT_EN_1_8G_UL3_Pin PATH_EN_2_1G_DL_Pin PATH_EN_2_1G_UL_Pin */
  GPIO_InitStruct.Pin = ATT_EN_1_8G_DL1_Pin|ATT_EN_1_8G_DL2_Pin|ATT_EN_1_8G_UL1_Pin|ATT_EN_1_8G_UL2_Pin 
                          |ATT_EN_1_8G_UL3_Pin|PATH_EN_2_1G_DL_Pin|PATH_EN_2_1G_UL_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOE, &GPIO_InitStruct);

  /*Configure GPIO pins : ATT_EN_1_8G_UL4_Pin PATH_EN_1_8G_DL_Pin PATH_EN_1_8G_UL_Pin PLL_EN_3_5G_L_Pin 
                           PLL_EN_3_5G_H_Pin */
  GPIO_InitStruct.Pin = ATT_EN_1_8G_UL4_Pin|PATH_EN_1_8G_DL_Pin|PATH_EN_1_8G_UL_Pin|PLL_EN_3_5G_L_Pin 
                          |PLL_EN_3_5G_H_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);

  /*Configure GPIO pins : PLL_EN_1_8G_DL_Pin PLL_EN_1_8G_UL_Pin ATT_EN_2_1G_DL1_Pin ATT_EN_2_1G_DL2_Pin 
                           ATT_EN_2_1G_UL1_Pin ATT_EN_2_1G_UL2_Pin ATT_EN_2_1G_UL3_Pin ATT_EN_2_1G_UL4_Pin */
  GPIO_InitStruct.Pin = PLL_EN_1_8G_DL_Pin|PLL_EN_1_8G_UL_Pin|ATT_EN_2_1G_DL1_Pin|ATT_EN_2_1G_DL2_Pin 
                          |ATT_EN_2_1G_UL1_Pin|ATT_EN_2_1G_UL2_Pin|ATT_EN_2_1G_UL3_Pin|ATT_EN_2_1G_UL4_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);

  /*Configure GPIO pins : PLL_LD_1_8G_DL_Pin PLL_LD_1_8G_UL_Pin */
  GPIO_InitStruct.Pin = PLL_LD_1_8G_DL_Pin|PLL_LD_1_8G_UL_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);

  /*Configure GPIO pins : PLL_DATA_Pin PLL_CLK_Pin ATT_DATA_Pin ATT_CLK_Pin 
                           DA_LDAC_Pin ATT_CLK_3_5G_Pin ATT_EN_3_5G_Pin ATT_DATA_3_5G_DL_Pin 
                           ATT_DATA_3_5G_UL_Pin ATT_DATA_3_5G_COM1_Pin ATT_DATA_3_5G_COM2_Pin ATT_DATA_3_5G_COM3_Pin 
                           PATH_EN_3_5G_L_Pin */
  GPIO_InitStruct.Pin = PLL_DATA_Pin|PLL_CLK_Pin|ATT_DATA_Pin|ATT_CLK_Pin 
                          |DA_LDAC_Pin|ATT_CLK_3_5G_Pin|ATT_EN_3_5G_Pin|ATT_DATA_3_5G_DL_Pin 
                          |ATT_DATA_3_5G_UL_Pin|ATT_DATA_3_5G_COM1_Pin|ATT_DATA_3_5G_COM2_Pin|ATT_DATA_3_5G_COM3_Pin 
                          |PATH_EN_3_5G_L_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);

  /*Configure GPIO pins : ALARM_DC_Pin ALARM_AC_Pin */
  GPIO_InitStruct.Pin = ALARM_DC_Pin|ALARM_AC_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);

  /*Configure GPIO pins : DA_SYNC_Pin DA_SCLK_Pin DA_DIN_Pin _T_SYNC_UL_Pin 
                           T_SYNC_UL_Pin _T_SYNC_DL_Pin T_SYNC_DL_Pin PATH_EN_3_5G_DL_Pin 
                           PATH_EN_3_5G_UL_Pin PLL_ON_OFF_3_5G_L_Pin PLL_ON_OFF_3_5G_H_Pin */
  GPIO_InitStruct.Pin = DA_SYNC_Pin|DA_SCLK_Pin|DA_DIN_Pin|_T_SYNC_UL_Pin 
                          |T_SYNC_UL_Pin|_T_SYNC_DL_Pin|T_SYNC_DL_Pin|PATH_EN_3_5G_DL_Pin 
                          |PATH_EN_3_5G_UL_Pin|PLL_ON_OFF_3_5G_L_Pin|PLL_ON_OFF_3_5G_H_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);

  /*Configure GPIO pins : PLL_LD_3_5G_L_Pin PLL_LD_3_5G_H_Pin */
  GPIO_InitStruct.Pin = PLL_LD_3_5G_L_Pin|PLL_LD_3_5G_H_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);

  /*Configure GPIO pin : PATH_EN_3_5G_H_Pin */
  GPIO_InitStruct.Pin = PATH_EN_3_5G_H_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
  HAL_GPIO_Init(PATH_EN_3_5G_H_GPIO_Port, &GPIO_InitStruct);

  /*Configure GPIO pins : PLL_EN_2_1G_DL_Pin PLL_EN_2_1G_UL_Pin */
  GPIO_InitStruct.Pin = PLL_EN_2_1G_DL_Pin|PLL_EN_2_1G_UL_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

  /*Configure GPIO pins : PLL_LD_2_1G_DL_Pin PLL_LD_2_1G_UL_Pin */
  GPIO_InitStruct.Pin = PLL_LD_2_1G_DL_Pin|PLL_LD_2_1G_UL_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

}

/* USER CODE BEGIN 4 */

/* USER CODE END 4 */

/**
  * @brief  This function is executed in case of error occurrence.
  * @retval None
  */
void Error_Handler(void)
{
  /* USER CODE BEGIN Error_Handler_Debug */
  /* User can add his own implementation to report the HAL error return state */

  /* USER CODE END Error_Handler_Debug */
}

#ifdef  USE_FULL_ASSERT
/**
  * @brief  Reports the name of the source file and the source line number
  *         where the assert_param error has occurred.
  * @param  file: pointer to the source file name
  * @param  line: assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t *file, uint32_t line)
{ 
  /* USER CODE BEGIN 6 */
  /* User can add his own implementation to report the file name and line number,
     tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
  /* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/